Dulux Professional® FASTFINISH™ Level 5 Prep Coat is a premium high film build prep coat designed to even out surfaces and help to create a level 5 finish. It has exceptionally high opacity and is very easy to sand. All Dulux Professional® products are designed to meet the application needs of painters.
Surface preparation
Ensure all surfaces are clean and dry prior to application. Brush down to remove dust. Thoroughly stir all products with a broad flat stirrer prior to application. Previously painted surfaces, except cement sheets, must be sanded to remove loose, peeling, flaking or chalky paint. Sand all gloss and semi gloss surfaces to a dull finish and wipe down with a damp cloth to remove surface dust. Spot prime bare areas.
Application
Spray only.
Airless spray advice
Tip size: 0.019"-0.021"
Pressure: 2000-2800 PSI
Coverage
Approximately 5m² per litre
Wash up
Water.
Thinning
Not usually required, but can be thinned with up to 100ml water per litre if necessary.
Drying time
Drying times on a day of about 25°C
Touch dry: 2 hours
Sand: 8 hours then recoat
Dulux Professional® FASTFINISH™ Undercoat and Ceiling Flat is a high-quality, dual-purpose interior paint that is designed to save time by undercoating walls and topcoating ceilings without stopping.
Sheen level
Flat
Surface preparation
Can be used on paper-faced plasterboard, MDF, masonry and suitably primed interior timber. Stir well before use. Apply one coat of Dulux Professional® FASTFINISH™ Undercoat & Ceiling Flat by airless spray to all chosen substrates. For ceilings, apply a second coat of Dulux Professional® FASTFINISH™ Undercoat & Ceiling Flat by spray as the finished coat. Back-rolling of the second coat may be performed to achieve the desired finish. For all areas other than ceilings, apply the suitable topcoats to finish. Please note that in each instance the first coat should be sufficiently dry before applying subsequent coats. Please note that Dulux does recommend the need to back-roll the ceiling to avoid glancing light issues. Learn more about spraying and back-rolling from the Dulux Technical Advice team.
Application
Spray
Airless spray advice
Tip size: 0.0015"-0.0019"
Pressure: 2000-2300 PSI
Coverage
Approximately 10m² per litre depending on the porosity of the surface.
Wash up
Water.
Thinning
Not required.
Drying time
Touch dry: 30 minutes
Recoat: 2 hours
Dulux Professional® FASTFINISH™ Dry Fall Ceiling is a flat premium acrylic ceiling paint designed specifically for spray application. Formulated with dry fall properties, it is suitable for interior ceilings and overhead surfaces. When applied to ceilings of a minimum three metres in height, the Dry Fall paint dries to a powder when the overspray particles reach the floor, allowing for easy clean up.
Sheen level
Flat
Surface preparation
Ensure all surfaces are clean and dry prior to application. Brush down to remove dust. Thoroughly stir all products with a broad flat stirrer prior to application. Previously painted surfaces, except cement sheet, must be sanded to remove loose, peeling, flaking or chalky paint. Sand all gloss and semi gloss surfaces to a dull finish and wipe down with a damp cloth to remove surface dust. Spot prime bare areas. Please ensure all areas are masked up prior to application. This product is formulated with DryFall properties, which when applied to ceilings of minimum 2.7 metres in height allows the paint to dry to a powder and fall to the ground for easy clean up.
Application
Spray
Airless Spray Advice
Tip size: 0.015"-0.019"
Pressure: 2000-2400psi
Coverage
Approximately 14m² per litre.
Wash up
Water.
Thinning
Not usually required, but can be thinned with up to 100ml water per litre if necessary.
Drying time
Drying time on a day of about 25°C
Touch Dry: 15 minutes
Re-coat: two hours
Dulux Professional® FASTFINISH™ Water Based Enamel are premium acrylic products suitable for use on interior and exterior doors, window frames and trim. They are a great alternative to traditional oil-based enamels with the benefits of using an acrylic paint.
Sheen level
Semi gloss, Gloss
Surface preparation
Ensure all surfaces are clean and dry prior to application. Brush down to remove dust. Thoroughly stir all products with a broad flat stirrer prior to application. Previously painted surfaces, except cement sheets, must be sanded to remove loose, peeling, flaking or chalky paint. Sand all gloss and semi gloss surfaces to a dull finish and wipe down with a damp cloth to remove surface dust. Spot prime bare areas.
Application
Spray, roller or brush
Airless spray advice
Tip size: 0.08" -0.012"
Pressure: 1500-1700 PSI
Air-assisted airless spray advice
Tip size: 0.08" -0.012"
Pressure: 900-1000 PSI
Coverage
Approximately 16m² per litre.
Wash up
Water.
Thinning
Not usually required, but can be thinned with up to 100ml water per litre if necessary.
Drying time
Drying times on a day of about 25°C
Touch dry: 30 minutes
Recoat: 2 hours under cool or humid conditions allow longer times. Ensure temperature is above 10°C during application and drying.
