Intergrain
UltraDeck Timber Oil Dark Oak
Intergrain
UltraDeck Timber Oil Dark Oak
About Intergrain UltraDeck Timber Oil Dark Oak
Intergrain UltraDeck® Timber Oil is a long lasting, high performance, water based coatingdesigned to enhance the natural colour of all exterior timber. The natural looking finish guardstimber against harsh weather conditions as well as the abrasive effects of foot traffic, providingyour timber superior protection for longer.
Key Points
- • Long lasting. • High traffic formula. • Coat in any season#
Quick guide
Cleaning materials
Water
Application Tools
Brush, Pad, Spray
Product specification
Precautions and limitations
Do not apply if:
- Humidity is higher than 85%
- Air or surface temperatures are above 35°C or below 5°C
- Rain or dew is expected before coating is rain ready ^
Performance guide
- Weather: Exterior durable
- Salt: Good
- Heat Resistance: Up to 70 degrees Celsius. Higher temperatures will cause film to soften.
- Water: Good
- Abrasion: Good
Surface preparation
Previously painted surface
The instructions below offer general preparation guidelines. For larger projects, commercial jobs or for more specific information please contact our Help & ; Advice team.
Maintenance coat of Intergrain UltraDeck Timber Oil
If your existing Intergrain UltraDeck Timber Oil coating is in good condition, clean the surface with Intergrain UltraPrep™ Timber Cleaner.
Grey and weathered with no previous coating
Clean with Intergrain UltraPrep Timber Cleaner. For severely weathered timber, sand back to a fresh surface, remove all sanding dust, then clean with Intergrain UltraPrep Timber Cleaner.
Existing coating in poor condition
Remove coating by using a combination of Intergrain UltraPrep Tannin & Oil Remover and power washing. Then clean with Intergrain UltraPrep Timber Cleaner.
Paints, varnishes or coatings in varied condition
Paints, varnishes or coatings that have deteriorated unevenly, remove all existing coating by using a coatings stripper or sanding back to bare timber. Then clean with Intergrain UltraPrep Timber Cleaner.
Important: If mould is present or if timber is in a mould prone area, use Intergrain UltraPrep Mould Killer to remove surface mould effectively as the first step of preparing the timber for coating.
Unpainted surfaces
New timber
Treat timber with Intergrain UltraPrep Tannin & Oil Remover. Then clean with Intergrain UltraPrep Timber Cleaner.
How to apply
Brush, Roller
Remove excess water from the surface and allow the timber to dry for at least 1 hour before coating.
Stir Intergrain UltraDeck Timber Oil thoroughly before and during use with a flat blade stirrer.
Apply Intergrain UltraDeck Timber Oil using the Intergrain DeckBrush (recommended), flat deck applicator, paint brush or spray (air assisted airless or airless). Do not use a roller.
Apply at the coverage rate of 10-14m2/L. Do not overspread or apply thinly as insufficient film thickness will result in lap marks and compromise performance and durability. When coating large areas, work in sections, apply long strokes and use natural breaks in the boards as stopping points. If spraying, it is recommended to back brush to even out the finish and avoid spotting.
Allow to dry following the recoat time indicated in the section typical properties, then apply a second coat. If necessary, sand lightly between coats to remove any raised grain.
A third coat will give extra protection and is required in harsh conditions such as full sun exposure, around pools and in humid areas or if the first coat was applied on damp or porous timber.
Important: All timber is required to be free from dust, mould and site contaminants prior to coating. Follow all relevant product label instructions when using Intergrain products.
Maintenance
Conduct a routine 12 monthly maintenance inspection. Best protection of the timber and ease of maintenance is ensured if Intergrain UltraDeck Timber Oil is recoated before deterioration of the coating and timber underneath occurs.
