FP (A&B) Satin (Part A)
Parts cannot be bought separately.
Need a DuluxTRADE account?Head into your local storeorenquire online now.
Surfaceshield® FP is a two component, non-sacrificial, waterborne fluoropolymer clear coat with excellent resistance to graffiti removing agents. The coating applies opaque on application and dries clear to ensure all sections of the surface are covered. Graffiti on surfaces treated with SURFACESHIELD® FP can be removed repeatedly once fully cured using a combination of graffiti removal agents and water.
Touch Dry
45 minutes
Re-coat
Minimum - 24 hours. Maximum - 3 days.
Cleaning materials
Water
Application Tools
Brush, Roller, Airless Spray
This is an industrial product designed for use by experienced Protective Coating applicators. This product contains isocyanates and appropriate PPE is required. Spray application is only suitable in controlled environments in accordance with state-based regulations. Where conditions may require variation from the recommendations on this Product Data Sheet contact your nearest Dulux® Consultant for advice prior to painting. Do not apply in conditions outside the parameters stated in this document without the written consent of DuluxGroup (Australia) Pty Ltd. Do not use any product past its pot life. Product past its pot life may still appear fit for use but will develop substantially reduced gloss and may develop brittleness. Freshly mixed material must not be added to material that has been mixed for some time. The rate of cure is dependent upon temperature. Do not apply at temperatures below 10°C, or where the surface temperature is below 10°C. Do not apply at relative humidity above 85% or when the surface is less than 3°C above the dewpoint. Ensure you read and understand the safety precautions on the Material Safety Data Sheets for the two components before using. You should only thin the mixed product with potable water. Do not add water to the PART B isocyanate component. Surfaceshield® FP will not reach its full anti-graffiti properties until fully cured.
The surface must be free from grease, oil, dirt, rust and other contaminants. Dulux recommends that surfaces be degreased with Gamlen CA 1 (a free-rinsing, alkaline detergent) according to the manufacturer’s written instructions and all safety warnings.
Previously painted surfaces: Degrease surface. Remove unsound coatings. Feather back edges to remove ridges. Abrade entire surface of tightly adhering remaining coating to remove gloss or chalkiness and provide a suitable key for the new coating system.
The surface must be free from grease, oil, dirt, rust and other contaminants. Dulux recommends that surfaces be degreased with Gamlen CA 1 (a free-rinsing, alkaline detergent) according to the manufacturer’s written instructions and all safety warnings.
Concrete: Concrete must be at least 28 days old before coating. Remove all laitance, form release agents, curing compounds, oil, grease and other surface contaminants.
NOTE: DO NOT ADD WATER TO PART B AT ANY STAGE.
1. Gently power mix each part (A and B) separately until the contents of each part is uniform.
2. Add Part B to Part A and power mix together thoroughly. Take care not to aerate - ensure that mixing does not draw in air and generate foam.
3. THIN 5% WITH POTABLE WATER. Add water only to the mixed product; NEVER ADD WATER TO PART B.
4. Continue mixing through the gel phase until product appears SMOOTH and consistent.
5. Let stand for 10 minutes.
6. Remix thoroughly before application.
Roller: Apply even coats of the mixed material to the prepared surface. Beyond the minimum 5% thinning, the mixed product may be further thinned with up to 50 ml/litre with potable water if needed. When rolling, additional coats may be required to attain the specified thickness.
Brush: Apply even coats of the mixed material to the prepared surface. Beyond the minimum 5% thinning, the mixed product may be further thinned with up to 50 ml/litre with potable water if needed. When brushing, additional coats may be required to attain the specified thickness
Airless Spray:
Standard airless spray equipment such as Graco Xtreme 30:1 with a fluid tip of 15-17 thou (0.38-0.43mm) and an air supply capable of delivering 550-690kPa (80-100 p.s.i.) at the pump. Ensure you think 5% with potable water.
- Tip Orifice: 15-17 thou (0.38-0.43mmm)
Conventional Spray:
Beyond the minimum 5% thinning, the mixed product may be further thinned with up to 50 ml/litre with potable water if needed.
- Gun: Graco AirPro
- Fluid Tip: 1.4mm
- Air Cap: 239542
- Atomising Pressure: 380 - 410 kPa (55-60 p.s.i.)
- Material Pressure: 70-100 kPa (10-15 p.s.i.)
