Dulux PRECISION® Premium Coatings Remover is a biodegradable and water-based product, which is effective for removing multiple layers of architectural and industrial coatings from interior\/ exterior surfaces. It is safer to use than traditional mechanical coatings removal systems, as it is designed to trap aged coatings in a wet state, preventing creation of airborne dust particles.
Touch Dry
N/A
Re-coat
N/A
Cleaning materials
Water
Application Tools
Brush, roller, spray* and trowel
Dwell time required for softening/lifting paint will vary according to the number of layers, type of coating being removed and surface temperature. Average dwell time ranges from 24-72 hours.
Application conditions
For best results, surface temperatures should be 10–30°C and approximatively 50% relative humidity. Product efficacy will be substantially reduced if applied outside of these conditions.
Test patch
Always perform a small inconspicuous test on each type of substrate and paint coating prior to full application. Testing prior to beginning any project is the best way to ensure product effectiveness. Test patches should be used to determine the proper dwell time and remover thickness to apply for the specific application. Failure to do a test patch may result in the need for more than one application, increasing costs and extending product timelines. Refer to Dulux Precision Test Patch Kit for further instructions.
Limitations
Not recommended for use on some plastics (flexible PVC unless it is part of a wall paper removal), most fiberglass, Plexiglas (acrylic sheeting), Polycarbonate sheeting, flexible rubber compounds and EIFS (Polystyrene) systems, as the active agents in the coating remover will plasticise these materials, permanently damaging their properties.
Care should be used when removing paint from smooth limestone, lime bound composite stone, including marble, rendered plaster and plasterboard, and cement based boards as the acid in the coating remover will react with the alkaline nature of these substrates, damaging the surface or the structural integrity of the substrate. For these surfaces it is recommended to use Dulux Precision Coatings Remover (green).
Care should be taken when removing paint from MDF, Particle Board and OSB (Oreinted Strand Board) as the surface particles of the board will swell and remain "furry" after removal of the paint requiring either heavy priming with a Level 5 primer, or a small amount of mechanical abrasion to smooth the surface.
Take care when using this product over Colorbond®/ColorSteel® surfaces as testing has shown that it is capable of removing the Colorbond®/ColorSteel® coating, taking it back to bare metal.
In some cases the coating remover will have a slight impact on reactive metals like galvanized steel and zinc and aluminium, but this will generally be minimal.
Limitations for spray
The Dulux Precision Coatings Remover range may be applied via spray. However, due to the corrosive nature of the product, it will lead to faster wear & tear of the spray machine and is likely to void the manufacturer’s warranty. For more details and specific information, please contact your Dulux representative.
NB: At the end of each day or at the end of the job rinse the spray machine thoroughly with water to prevent any of the Precision Coatings Remover drying on the surface or within the hopper and gun.
Disposal
Always investigate and confirm disposal means allowed in the jurisdiction that you are operating before starting a job. It is important to know what is allowed and the costs of doing so in order to properly quote the finished removal costs.
Always perform a small inconspicuous test on each type of surface/paint coating to be removed before general use to determine compatibility, yield, proper thickness and dwell time needed.
Remove any loose or peeling paint prior to application. Mask/protect areas where stripping is not desired.
Using a brush, roller, trowel or spray*, apply product approximately 1.5mm - 3.5mm thick (refer to test patch results), according to number of layers and type of coating being removed.
*The Dulux Precision Coatings Remover range may be applied via spray. However, due to the corrosive nature of the product, it may damage or lead to faster wear & tear of the spray machine and is likely to void the manufacturer’s warranty. For more details and specific information, please contact your Dulux representative.
Post application, cover the product with the special laminated paper, printed side facing out. Use tape to create an airtight seal along the edges to allow the coating remover to work at maximum strength.
Allow product to dwell on the surface for 1-72 hours (based on test patch results), then remove softened/lifted paint using a metal scraper. Agitate surface residue with a stiff nylon brush or scouring pad, paying particular attention to crevices, grooves and cracks.
Exterior stripped surfaces should be rinsed thoroughly with fresh water. Interior surfaces can be rinsed using a sponge and soapy water.
Collect paste and paint residue in plastic bags and dispose of in compliance with government regulations. Clean up airless sprayer by running water or denatured alcohol through the equipment soon after application has been completed. Allow surface to dry thoroughly before repainting.
